DrainageCalculators

Open Channel Flow Calculator for Rectangular, Trapezoidal & Triangular Channels

Calculate discharge, velocity, hydraulic radius, wetted perimeter, or normal depth with Manning's equation for rectangular, trapezoidal, triangular, parabolic, and surveyed open channels.

Try a Common Scenario

Click to pre-fill the calculator with realistic values.

Open-channel capacity from geometry, roughness, and slope

Manning’s equation gives mean velocity as V = (k/n)R2/3S1/2 and discharge as Q = A·V. This calculator derives the flow area A, wetted perimeter P, and hydraulic radius R = A/P for the selected cross-section, or solves the normal depth for a known discharge.

Input Parameters

Channel Shape

Flow Parameters

ft

Known water depth; discharge will be computed

ft/ft

Longitudinal slope of channel bed

Roughness coefficient for channel material

View Manning's n Reference Table

Channel Geometry

ft

Width of the channel bottom

Ready to Calculate

Enter your channel parameters and click Calculate to see results.

For educational purposes only. Not a substitute for professional engineering judgment.

Interactive model

Manning open-channel prism

Compare rectangular, trapezoidal, and triangular cross-sections while flow area and wetted perimeter drive Manning discharge.

Open full model (opens in a new tab)

About Manning's Equation for Open Channels

Manning's equation is an empirical formula used to calculate the velocity of flow in open channels. It relates the flow velocity to the channel's hydraulic radius, slope, and roughness coefficient.

The Manning Equation

V = (k/n) * R2/3 * S1/2

Where:

  • V = Mean velocity (ft/s or m/s)
  • k = Conversion factor (1.486 for US units, 1.0 for SI)
  • n = Manning's roughness coefficient
  • R = Hydraulic radius = A/P (ft or m)
  • S = Channel slope (ft/ft or m/m)

Supported Channel Shapes and Solve Modes

Enter a known depth to compute discharge, or enter a known discharge to solve normal depth. The same numerical engine drives the Compute Curves table for depth, flow, slope, and roughness sweeps.

  • Rectangular - Common for lined channels, flumes, and box culverts
  • Trapezoidal - Most efficient for earthen channels and roadside ditches
  • Triangular - Used for gutters, V-ditches, and small swales
  • Parabolic - Natural channel shape, grass-lined swales
  • User-defined - Surveyed station/elevation vertices with a separate Manning’s n on each boundary zone

For varying roughness, contiguous equal-n segments are combined into hydraulic subareas. Their conveyances are summed and the equivalent composite n is reported using the Lotter method, matching the FHWA Hydraulic Toolbox workflow. Circular sections are already covered by the Manning’s Pipe Flow calculator.

Key Parameters

  • Hydraulic Radius (R) - Ratio of flow area to wetted perimeter
  • Wetted Perimeter (P) - Length of channel boundary in contact with water
  • Froude Number (Fr) - Ratio of inertial to gravitational forces; indicates flow regime
  • Specific Energy - Sum of flow depth and velocity head
  • Critical Hydraulics - Critical depth, velocity, and slope for the computed flow
  • Boundary Shear - Average γRS and FHWA maximum approximation γyS

Channel geometry: area, wetted perimeter, hydraulic radius and top width

Manning’s equation needs the flow area A and the hydraulic radius R = A/P at the flow depth y. These are the section formulas the calculator uses. The side slope z is the horizontal run per 1 unit of rise (zH:1V) on each side; keep every length in the same unit (ft or m).

Trapezoidal channel section showing bottom width b, flow depth y, top width T and side slope z horizontal to 1 vertical T y b 1 z
Section Area, A Wetted perimeter, P Hydraulic radius, R = A/P Top width, T
Rectangular bottom width b, depth y b·y b + 2y b·y / (b + 2y) b
Trapezoidal b, y, side slope z (zH:1V) (b + z·y)·y b + 2y√(1 + z2) (b + z·y)·y / [b + 2y√(1 + z2)] b + 2z·y
Triangular (V-ditch) y, side slope z (zH:1V) z·y2 2y√(1 + z2) z·y / [2√(1 + z2)] 2z·y
Circular (partly full) diameter D, y; θ = 2 cos−1(1 − 2y/D) in radians D2(θ − sin θ) / 8 D·θ / 2 (D/4)(1 − sin θ / θ) D·sin(θ/2)

The hydraulic depth D = A/T sets the Froude number, Fr = V/√(gD). This calculator covers the open shapes; for a circular pipe use the Manning’s pipe flow calculator, which applies the circular formulas above.

Worked example: trapezoidal channel flow (US units)

An excavated earth channel with short grass (n = 0.027, Chow (1959) Table 5-6) has a 4 ft bottom width, 3H:1V side slopes and a bed slope S = 0.005 ft/ft. How much does it carry flowing 1.5 ft deep?

  1. Flow area A = (b + z·y)·y = (4 + 3 × 1.5) × 1.5 = 12.75 ft²
  2. Wetted perimeter P = b + 2y√(1 + z2) = 4 + 2 × 1.5 × √10 = 13.49 ft
  3. Hydraulic radius R = A/P = 12.75 / 13.49 = 0.945 ft
  4. Velocity V = (1.486/n)·R2/3·S1/2 = 55.04 × 0.9632 × 0.07071 = 3.75 ft/s
  5. Discharge Q = V·A = 3.75 × 12.75 = 47.8 cfs
  6. Flow regime T = b + 2z·y = 13.0 ft, so D = A/T = 0.981 ft and Fr = V/√(gD) = 3.75 / √(32.174 × 0.981) = 0.67: subcritical flow.

Working the other way, a design flow of 30 cfs in the same channel runs at a normal depth of 1.20 ft and 3.31 ft/s. Select Enter flow (solve depth) in the calculator to reproduce it, then check the velocity or shear against the lining’s permissible limit (FHWA HEC-15) before you accept the section.

Worked open-channel shape examples

These examples use the same calculation engine as the tool above. Compare A/P and R to see why cross-section geometry changes capacity even when depth, slope, and roughness are similar.

Rectangular concrete channel

6 ft bottom width, 2 ft flow depth, n = 0.013, and S = 0.010 ft/ft.

Area, A
12.00 ft²
Wetted perimeter, P
10.00 ft
Hydraulic radius, R
1.200 ft
Velocity, V
12.91 fps
Discharge, Q
154.90 cfs

Trapezoidal earthen ditch

4 ft bottom, 2 ft deep, 2H:1V side slopes, n = 0.025, and S = 0.005.

Area, A
16.00 ft²
Wetted perimeter, P
12.94 ft
Hydraulic radius, R
1.236 ft
Velocity, V
4.84 fps
Discharge, Q
77.45 cfs

Triangular metric V-ditch

0.6 m deep, 3H:1V side slopes, n = 0.030, and S = 0.010 m/m.

Area, A
1.08 m²
Wetted perimeter, P
3.79 m
Hydraulic radius, R
0.285 m
Velocity, V
1.44 mps
Discharge, Q
1.56 cms

Need to find depth instead of discharge? Select Enter flow (solve depth) in the calculator to solve the Manning normal depth for any supported shape, then compare it with the critical depth.

Frequently asked questions

What is Manning's equation for open channel flow?

Manning's equation gives the mean velocity of steady, uniform flow as V = (k/n) R^(2/3) S^(1/2), and the discharge as Q = V × A. Use k = 1.486 with feet and cfs, or k = 1.0 with metres and m³/s. A is the flow area, R = A/P is the hydraulic radius (flow area divided by wetted perimeter), S is the energy slope (the bed slope in uniform flow) and n is the Manning roughness coefficient.

How do I calculate the cross-sectional area of a channel?

Work it out from the section shape at the flow depth y. A rectangle of bottom width b has A = b·y; a trapezoid with zH:1V side slopes has A = (b + z·y)·y; a symmetric V-ditch has A = z·y²; and a partly full circular pipe has A = D²(θ − sin θ)/8, with θ = 2 cos⁻¹(1 − 2y/D). The geometry table on this page gives the wetted perimeter, hydraulic radius and top width for the same shapes.

What is Manning's equation for a trapezoidal channel?

Substitute the trapezoid's geometry into Q = (k/n)·A·R^(2/3)·S^(1/2), with A = (b + z·y)·y, P = b + 2y√(1 + z²) and R = A/P. For example, a 4 ft bottom width with 3H:1V sides flowing 1.5 ft deep at S = 0.005 and n = 0.027 carries about 47.8 cfs at 3.75 ft/s (see the worked example on this page).

What is normal depth in open channel flow?

Normal depth is the depth at which a given discharge flows uniformly, so the water surface, the energy line and the channel bed are parallel. Most shapes have no closed-form solution, so it is found by trial or numerically: choose "Enter flow (solve depth)" in the calculator. In the worked example, 30 cfs flows at a normal depth of 1.20 ft.

Reference & standards

Was this calculator helpful?

Last verified: August 2026